- #Lg cd rom crn 8245b driver serial#
- #Lg cd rom crn 8245b driver driver#
- #Lg cd rom crn 8245b driver software#
- #Lg cd rom crn 8245b driver code#
Mptscsih: ioc0: WARNING - Issuing HardReset!! Mptscsih: ioc0: WARNING - TM Handler for type=1: IOC Not operational (0x40008112)! Mptscsih: ioc0: attempting task abort! (sc=f7862e80) Target0:0:0: mptspi: ioc0: dma_alloc_coherent for parameters failed
#Lg cd rom crn 8245b driver code#
Mptbase: ioc0: WARNING - FAULT code = 8112h Mptbase: ioc0: WARNING - IOC is in FAULT state!!! Modules linked in: ide_pci_generic(+) floppy mptspi(+) mptscsih ohci_hcd tg3 mptbase scsi_transport_spi usbcore serverworks ide_core ata_generic libata scsi_mod dock thermal processor fan thermal_sys IP: :mptspi:mptspi_dv_renegotiate_work+0xa/0x9f Mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009!īUG: unable to handle kernel NULL pointer dereference at 0000034c I left it running for 8 minutes for this.
#Lg cd rom crn 8245b driver serial#
This is the boot error message obtained with serial cable.
![lg cd rom crn 8245b driver lg cd rom crn 8245b driver](https://www.helpowl.com/manualimages/v/5/lg-gcr8520b-owners-manual-ea72587_5_8708.png)
Scsi 0:0:8:0: Attached scsi generic sg2 type 3 Scsi 0:0:1:0: Attached scsi generic sg1 type 0 Sd 0:0:0:0: Attached scsi generic sg0 type 0 Scsi 0:0:8:0: Processor IBM 25P3495a S320 1 1 PQ: 0 ANSI: 2ĭriver 'sd' needs updating - please use bus_type methods Scsi 0:0:0:0: Direct-Access IBM-ESXS DTN018C1UCDY10F S23J PQ: 0 ANSI: 3 Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- GSI 24 (level, low) -> IRQ 24 This is the verbose lspci of the controller (obtained with 2.6.25):Ġ1:01.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)Ĭontrol: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx. I will paste these at the end of this post. I obtained two of those on different boots. I connected a serial cable in order to obtain the boot error message.
#Lg cd rom crn 8245b driver driver#
I tried to forward-port the Fusion driver from 2.6.25 to 2.6.26-rc7 by simply copying over the directory drivers/message/fusion/ from 2.6.25 to 2.6.26-rc7 but unfortunately this doesn't compile, so I am stuck not being able to use 2.6.26 on this machine (actually I have not tried versions of 2.6.26 earlier than rc7. Doing the same with 2.6.25, basically the same config file, boots without problems. I compiled 2.6.26-rc7 on a machine with controller LSI53C1080 and it cannot boot. It seems to me that a bug was added to the MPT Fusion driver in 2.6.26 (rc7). I'm no kernel expert, I hope I made no mistakes in this report. Problem Description: MPT Fusion error, unbootable, see below
![lg cd rom crn 8245b driver lg cd rom crn 8245b driver](https://i.ebayimg.com/images/g/sKUAAOSwvytgqhIi/s-l400.jpg)
#Lg cd rom crn 8245b driver software#
Software Environment: error and hangup at boot
![lg cd rom crn 8245b driver lg cd rom crn 8245b driver](https://http2.mlstatic.com/D_NQ_NP_690215-MLB25138805947_112016-O.jpg)
Earliest failing kernel version: 2.6.26-rc7ĭistribution: Debian (but vanilla kernel)